Module 32

    

Updated: 07/09/2006

Module 32

 

 

 

The Fill, Back and

Background Lights

 

 

 

We've noted that the key light establishes the dimension, form, and surface detail of subject matter. Although the remaining lights have less important roles, they are nevertheless critical in creating an acceptable lighting effect.

The key light by itself — whether it's the sun in a clear sky or a focused quartz light in the studio — produces distracting shadows. (We'll see some examples later.) The purpose of the fill light is to partially (but not entirely) fill in the shadows created by the horizontal and vertical angles of the key light.    

 

The Fill Light

top view of key, fill, and back light placementIdeally, the fill light should be about 90 degrees away from the key light.

This means that if you draw lines from the key to the subject and then to the fill light, you'll create a right angle.

Although the fill can be positioned at any point from right beside the camera to 45 degrees away, it's safest to place the fill 45 degrees from the camera.

By lighting a full 90 degree area, an important margin of safety is created in case subjects unexpectedly move and camera angles have to be changed during the production.

Having to stop a production to change the position of lights can represent a time-consuming and costly delay — not to mention, making you a bit unpopular with the cast and crew.

Although the horizontal angle for the key should be about 45-degrees, the vertical angle of the fill is less critical.

side view of lights in studio pantograph to position lights'

Generally, the fill is placed just above the camera, as shown above, which means it ends up being slightly lower than the key. In this position it can easily do what it's intended to do: partially fill in the shadows created by the key light.

The height of the fill can be lowered from the grid to the proper angle by an extension rod (pipe) or by a counterbalanced extension device shown above on the right. close-up of subject with proper lighting

We've suggested that the fill light should be softer than the key. A soft light source is able to subtly fill in some of the key's shadows without creating a second catchlight in the eyes.

Note in the photo here how the shadow from the key on the cheek is only partially removed by the fill, creating a gradual rounding off of the key light on the cheek.

This key-fill difference provides much of the perception of three dimensions that's desirable in a medium that's limited to two dimensions. 
 

 

Fill Light Options

Agood choice for a studio fill light is a scoop, or a bank of color-balanced fluorescents.

When doing on-location work these options are a bit unwieldy, so a portable quartz stand light can be used with a diffuser. The diffuser not only softens the fill light, but it can appropriately reduce its intensity. We'll cover the relative intensity of each of the lights in the next module.

Outside, reflector board used on ENG shootwhen the sun is being used as a key, a reflector board can be positioned at about 90-degrees from the sun to reflect sunlight into the shadow areas.

Large white Styrofoam or foam core boards are often used in doing close-ups. A large blank, white artist canvass in a wooden frame, available at most artist supply stores, is being used here.

Although more expensive, folding silver reflectors, available at photo supply stores, are easier to transport and can reflect light much greater distances. Reflector boards can be clipped to a stand, or held by an assistant.

effect of fill reflector on subject subject in sunlight without fill

 

These photos illustrate a subject in harsh sunlight with and without a reflector fill.

 

 

 

If a key light puts out a wide beam of light, part of this light can be bounced off of a reflector board to act as a fill.

use of reflector board for fill

  

The Back Light

At this point in formula lighting we've covered two of the three lights on the subject.

The third point is represented by the back light. The function of the back light is to separate the subject from the background by creating a subtle rim of light around the subject.

top view of light placements

 

backlight on subject


The back light, sometimes called a hair light, should be placed directly behind the subject in relation to the close-up camera .

From an overhead perspective you should be able to draw a straight line from the lens of the close-up camera, through the subject, directly to the back light. Note drawing above.

positions of major studio lightsAlthough the elevation of the back light is often dictated by conditions, a 45 degree angle is most desirable.

If the back light is too low, it will be picked up by the camera in wide shots; if it's too high it will spill over the top of the subject's head, lighting up the tip of the nose, creating "the Rudolph effect," after a well-known reindeer.

Compared to the key, a smaller, lower-wattage instrument can be used for a back light for two reasons. First, back lights are often placed closer to the subject than the key light, and, second, with subjects confined to a limited area like a chair, the beams of most Fresnel lights can easily be "pinned down" (focused into a narrower beam) to intensify the beam.

By using only back lights with no front lighting a silhouette effect can be created. This can be used for dramatic effects or to hide someone's identity. (Note the photo of the woman reading the script above.) In trying to successfully eliminate all front lighting—especially in an effort to hide someone's identity—watch out for reflected light from walls and the floor.  

backlit subject #1

Outside the studio, the use of back light (generally in the form of sunlight) can add depth and separation to subject matter.

Note the effect of strong backlight in these two photos. backlit subject #2

 

 


division markerAt the same time, strong back light without adequate front light can create an exposure problem—unless you intentionally want to achieve a silhouette effect.  

Remember, on many camcorders there is a back light control that's designed to compensate (to some degree) for this exposure problem.  A careful balance between front light and back light can add a 3-D quality to scenes.

At this point you should study the effects of the various lights as ? shown here .

 

 

Background Lights

Background lights are used to illuminate the background area and add depth and separation between scene elements. (Remember that a back light is designed to light up the back of subjects and a background light is designed to light up the front of backgrounds .) The effect of the backlight is shown below.

backlight only


Once the background light is added, the lighting setup is complete, as shown in the drawing on the right above.

Any type of light can be used as a background light as long as it provides fairly even illumination across the background, does not hit the central subject matter, and is at the appropriate intensity.

If the background has detail or texture, you will want to put the background light on the same side as the key, as shown in the drawing above. This keeps the dominant light consistent in the scene.

Note in the photo on the left above that you can see the effect of both the back light and the background lights.

This brings us to the last major issue in formula lighting: the relative intensity of each of the lights. We'll cover that in the next module.

To see all of the lights we've discussed and their effect carefully study ? this photo .



       TO NEXT MODULE         Search Site          Video Projects          Revision Information            
              Issues Forum                    Associated Readings          Bibliography             
     Index #2 for Mobile Modules            To Home Page                   Tests/Crosswords/Matching       

© 1996 - 2006, All Rights Reserved.
Use limited to direct, unmodified access from CyberCollege® or the InternetCampus®
.